Lg art cool service manual pdf

Page 5 Safety Precautions Ensure that an installation Do not disassemble or repair Do not install the product at a frame of the outdoor unit is the product randomly. Page 6 Safety Precautions Keep the flames away.

Take the power plug out if neces- Do not use the power cord sary, holding the head of the plug near the heating tools. Page 7 Safety Precautions Installation Install the drain hose to Install the product so that the Always inspect gas leakage ensure that drain can be noise or hot wind from the after the installation and repair securely done. Page 8: Dimensions Dimensions Dimensions Symbols used in this Manual This symbol alerts you to the risk of electric shock.

This symbol alerts you to hazards that may cause harm to the air conditioner. This symbol indicates special notes. Push the front panel backward and lift it up to remove the two screws. As soon as you lift the both lower parts of panel front, you can hear the sound from panel front. At this moment panel front is separated 3. Attach an Installation guide map on the 6.

Look at suited horizon by horizontal desired surface. Carry out correct flaring work in the following procedure. Cutting the pipes and the cable. Use the piping kit accessory or the pipes purchased Copper locally. Compare the flared work with the figure by. Inside is shiny without scratches 2. Inclined Surface Cracked Uneven damaged thickness Page 15 Installation Connecting the pipings with the indoor unit and drain hose with drain pipe 1. Align the center of the pipings and sufficiently tighten the flare nut by hand.

Indoor unit tubing Flare nut Pipes 2. Tighten the flare nut with a wrench. Outside diameter Torque Open-end wrench fixed Page 16 Installation Outdoor Align the center of the pipings and sufficiently tighten the flare nut by hand. Finally, tighten the flare nut with torque wrench until the wrench clicks. Ensure that the color of the wires of the outdoor unit and the terminal No.

Remove the control cover from the unit by loos- Outdoor Unit ening the screw. Connect the wires to the terminals on the control Terminal block board individually. Secure the cable onto the control board with the Over 5mm cord clamp.

Checking the drainage. Bubbles indicate a leak. Page 21 Installation Soap water method Gas side 1 Remove the caps from the 2-way and 3-way valves. First, Check the side cover assembly exactly, and fix the power cord in the bottom groove of cover side left.

Carry out correct flaring work in the following proce- dure. Cutting the pipes and the cable. Use the piping kit accessory or the pipes purchased locally. Compare the flared work with the figure by. Inside is shiny without scratches 2. Inclined Surface Cracked Uneven damaged Page 12 Installation Connecting the piping with the indoor unit and drain hose with drain pipe 1.

Align the center of the pipings and sufficiently tight- en the flare nut by hand. Indoor unit tubing Flare nut Pipings 2. Tighten the flare nut with a wrench. Follow the instruction below. Drain Piping 1 To check the drainage. First, Check the side cover assembly exactly, and fix the power cord in the bottom groove of cover side left.

Assemble connecting lead wire with controller, fix the upper part of panel front, and match the lower part of panel front. Ensure that the color of the wires of the outdoor unit and the terminal No.

Remove the battery cover by pulling it according to the arrow direc- tion. Please fix tightly using provided screw after placing remote controller setup board on the place where you like to setup. Please set up remote controller board fit to the reclamation box if there is a reclamation box. Please connect indoor unit and remote controller using connection cable. Please check if connector is normally connected.

Indoor Unit side Connecting cable 5. Please use extension cable if the distance between wired remote controller and indoor unit is more than 10m. Incorrect operation due to ignoring any instructions will cause harm or damage. Page 7: Unit Parts unit Parts Single Zone Art Cool Gallery The following table shows the available outdoor and indoor units, their model numbers, along with the factory provided controller.

Pressing the enables the user to set the actual time as shown on the display screen. Insert AAA batteries 1. Remove the battery cover from the back of the unit, by pushing down the tab at the top of the cover 1 Figure 2. Page 11 unit OPeratiOn remote Control, Indoor unit Single Zone Art Cool Gallery initializing Operation of remote Control To begin communication between the indoor unit and the remote control, point the remote control towards the signal receiver, located at the bottom right hand corner of the indoor unit see Figure 6.

On the Remote Control, press to turn on the power to the 1. On the Remote Control, press to turn on the power to the indoor unit. Page 13 basiC funCtiOns Timer Setting Functionality setting the timer The Art Cool Gallery unit can be programmed through timer settings to turn on and off at set times during the day and night. This functionality allows you to save energy and utilize the air conditioner more efficiently.

It increases the set temperature to the optimal level for a restart reboot and remember its previous settings. Page Maintenance MaintenanCe Indoor unit - Cleaning Interval Clean the product regularly to maintain optimal performance and to prevent possible breakdown. Refer to Figure 11 for the basic components of the indoor unit.

Refer to Table 4 for detailed instructions on maintenance.